服務咨詢電話:18128116842

汽車清洗設備
您當前的位置 : 首 頁 > 產品中心 > 其他

動力轉向清洗專用設備

產品屬性

  • 所屬分類:其他
  • 產品編號:1570848696
  • 瀏覽次數:0
  • 發布日期:2019-10-21
  • 產品概述
  • 性能特點
  • 技術參數

動力轉向清洗專用設備

經過培訓后的合格人員才可使用該設備。只有在閱讀和明白以下規定后才可使用和操縱該設備。

嚴禁在設備操作過程中吸煙,遠離火源。操作人員應佩戴護目鏡。

切勿吸入由清洗機和方向機散發出的清洗液霧氣。

請在通風條件良好的場地使用該設備。

請仔細閱讀所使用產品的“安全使用注意事項”。

如果清洗設備與車輛接口處有滲漏,應立即修理好。

如果濺出和滲漏的清洗液滴落于皮膚和眼睛時,應立即用清水清洗。

請在清洗設備附近配備滅火器。

設備使用時,切勿將壓力調至超過設備的額定參數,否則設備會受到嚴重損害,容易造成安全事故。

未經我公司檢驗推薦,嚴禁使用非本品牌的清洗液,否則,引發的設備及人員傷亡事故,我公司不承擔任何法律責任。


設備的維護和保養:

保持ZC-9600設備的外觀清潔。

定期檢查設備的電源線路和接頭是否完好。

定期檢查設備內保險管是否正常。

定期清理設備舊油桶內的舊油。

快不允許使用本設備抽取其它油類(如制動油等)。


常見故障的處理方法:

1.指示燈不亮或電泵不工作,請先檢查保險管是否燒壞或內部電源插頭有無脫落。

2.交換不等量,請先打開設備的舊油抽取開關,然后在開啟加注新油的開關。


動力轉向清洗專用設備操作流程

ZC-9600

di一步

清洗作業

1、將ZC-9600設備上的電源線與保養車輛的電池連接,紅色接正級,黑色接負級。注意:不可接反!

2、找到車輛方向機儲油壺,將油壺蓋打開并放好。

3、將ZC-9600設備控制盒油管插入動力轉向油壺底部。打開控制上抽油開關,抽取適量舊油。

4、向動力轉向油壺中加入一瓶清洗產品。

5、啟動車輛自由轉動方向盤,左右全方向交替轉動,運行5--10分鐘,可以有效的清洗液力轉向系統中的油泥和雜質。


注意事項:

1、電源正負極不可接反;

2、應檢測輪胎氣壓是否正常;

3、應檢查車輛動力轉向液量是否合適,管路是否破損或有泄漏;

4、抽出舊油量與加入的清洗劑劑量相同,以滿足車輛清洗時的需要。 


第二步

換油作業


1、向ZC-9600設備儲油罐中添加新方向機油。根據車輛動力轉向系統進出油管的高低分布,調整抽、加油管道位置。將抽油管道盡量插入動力轉向油壺底部。

2、先打開控制盒抽油開關抽取舊油。當部份舊油被抽出回到ZC-9600設備中時,打開控制盒加注開關,向車輛注入新方向機油。

3、當新油視窗和舊油視窗顏色相近時,關閉控制盒所有開關,啟動車輛并來回轉動方向盤1至2分鐘。

4、停止發動機運轉,打開設備上所有開關進行換油,當新油和舊油顏色相近時,關閉設備上的所有開關,啟動車輛并左右轉動方向盤1至2分鐘。

5、重復第4步一次,確認新油視窗和舊油視窗液顏色相近后,換油結束。

6、向車輛動力轉向油壺中加入一瓶超級保護劑。確認油壺中的油量是否在規定的刻度,不足請添加。


注意事項

1、設備中的舊油需定期排放。

2、先抽取舊油后才進行新油加注,整個過程需交替進行,直至油壺內油液全部更新,由于轉向系統中液壓油并非全部流動,所以少量的舊油殘余是被允許的;

3、如交換出的舊油中有較多的金屬粉末時,必須立即提醒客戶檢查轉向系統其他機件;

4、不可在啟動的狀態下,將油液全部吸出再加注,以防以液壓助力泵損壞;

5、在發動機運行狀態下,方向盤左右轉動極限停留時間不可超過5秒。

6、交換過程中如出現異常應該立即停止檢查;

7、作業完成后請檢查轉向系統是否存在異常;


The equipment can be used by qualified personnel after training. The equipment can be used and operated only after reading and understanding the following rules.


do not smoke during the operation of the equipment and keep away from the fire source. Operators should wear goggles.


do not inhale the liquid mist from the cleaning machine and the direction machine.


please use the equipment in a well-ventilated area.


please read carefully the "safety precautions" of the products you use.


if the cleaning equipment is leaking from the vehicle, it should be repaired immediately.


wash with clean water immediately if dripping and leaky cleaning fluid drop to the skin and eyes.


please equip your cleaning equipment with fire extinguishers.


when the equipment is used, do not adjust the pressure to the rated parameters of the equipment, otherwise the equipment will be seriously damaged, which can cause a safety accident.


without my company's inspection recommendation, it is strictly prohibited to use the cleaning liquid of the brand, otherwise, the equipment and personnel casualties caused by the accident will not be held liable for any legal liability.


Equipment maintenance and maintenance:


Keep the appearance of zc-9600 equipment clean.


Check the power lines and joints of the equipment regularly.


Regularly check whether the equipment is normal.


Regularly clean the old oil in the old tank.


It is not allowed to use this equipment to extract other oils (such as brake oil).


Common fault handling methods:


1. The indicator light is not bright or the electric pump does not work, please check whether the insurance tube is burnt or the internal power plug is off.


2. In exchange for a different amount, please open the old oil extraction switch of the device and then switch on the new oil.


Power shift to clean special equipment operation flow


ZC - 9600.


First step


cleaning


1. Connect the power cord on the zc-9600 equipment to the battery connection of the maintenance vehicle, red to the positive and black to negative. Note: do not answer!

2. Find the car's direction machine for oil storage pot, open the oil pot lid and put it away.

3. Insert the zc-9600 equipment control box to the bottom of the oil pot. Open and control the oil switch and extract the appropriate amount of old oil.

4. Add a bottle of cleaning product to the power steering oil pot.

5. Start the vehicle to turn the steering wheel freely, rotate around the whole direction, and run for 5--10 minutes, which can effectively clean the oil sludge and impurities in the system.


Notes:


1. The power supply is negative;

2. Check whether the tire pressure is normal;

3. Check whether the vehicle power steering fluid is suitable, whether the pipeline is broken or leaking;

4. The amount of the old oil shall be the same as the dose of the detergent added to meet the needs of the vehicle cleaning.


The second step


Change the oil


1. Add new direction oil to the zc-9600 equipment storage tank. According to the vehicle power steering system in and out of the pipeline, adjust the position of pumping and filling. Insert the pumping pipe as much as possible to the bottom of the oil pot.

2. Open the control box to extract the old oil. When part of the old oil is pumped back into the zc-9600 equipment, open the control box to add the switch, and inject new direction oil into the vehicle.

3. When the new oil window is similar to the old oil window, turn off the control box on all switches, start the vehicle and turn the wheel back and forth for 1 to 2 minutes.

4, stop the engine running, open all switch device for an oil change, when the old and new oil oil color close, close all the switch on the equipment, launch vehicles and turn the steering wheel around 1 to 2 minutes.

5. Repeat step 4 to confirm that the new oil window and the old oil window are similar in color and the oil is finished.


Add a bottle of super protectant to the car's power steering. Confirm whether the oil in the oil pot is on the specified scale. Please add.


considerations


1. The old oil in the equipment needs to be discharged regularly.

2, first makes a new oil filling of the old oil after the process should continue until the oil in oil can update, due to the hydraulic oil flow is not all in the steering system, so a small amount of old oil residue is allowed;

3. If there are more metal powder in the exchanged old oil, the customer must be reminded to check the other parts of the steering system immediately.

4. Do not pump out the oil in the state of start-up, in case it is damaged by hydraulic power pump;

5. In the operating state of the engine, the limit of rotation of the steering wheel shall not exceed 5 seconds.

6. During the exchange process, any abnormality should be stopped immediately;

7. Please check whether the steering system is abnormal after completing the job.


標簽

上一篇:發動機過濾器2019-10-21
下一篇:柴油清洗吊瓶2019-10-21

最近瀏覽:

相關產品

相關新聞

聯系我們:

電話:0760-86637060

手機:18128116842

傳真:0760-86637050

郵箱:551660872@qq.com

網址:www.915uc.com

地址:中山市坦洲鎮振興北路1號

底部導航:

產品中心                成功案例

關于我們                新聞中心

招商加盟                聯系我們

二維碼:
Copyright ? 珠海市志誠汽車保養設備科技有限公司 All rights reserved 備案號:粵ICP備14002069號-1 專業從事于汽車養護設備,汽車保養設備,汽車清洗設備, 歡迎來電咨詢! 技術支持:祥云平臺 服務支持:澳捷信息
荔枝视频下载app污最新版免费观看,荔枝视频下载安装黄